| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136 |
- # hw definition file for processing by chibios_pins.py
- # old F412 layout
- MCU STM32F4xx STM32F412Rx
- # board ID for firmware load
- APJ_BOARD_ID 9
- # crystal frequency
- OSCILLATOR_HZ 24000000
- STM32_HSE_ENABLED FALSE
- STM32_PLLM_VALUE 16
- STM32_PLLN_VALUE 384
- STM32_PLLP_VALUE 4
- STM32_PLLQ_VALUE 8
- STM32_PLLSRC STM32_PLLSRC_HSI
- STM32_PREE1 STM32_PREE1_DIV2
- STM32_PREE2 STM32_PREE2_DIV1
- STM32_PWM_USE_TIM3 TRUE
- # board voltage
- STM32_VDD 330U
- # flash size
- FLASH_SIZE_KB 1024
- # serial port for stdout
- STDOUT_SERIAL SD2
- STDOUT_BAUDRATE 115200
- # order of I2C buses
- I2C_ORDER I2C2 I2C1
- # order of UARTs
- UART_ORDER USART2 USART6 USART3
- PC0 MGND ADC1
- PC1 PWM4_SENSE ADC1
- PC2 PWM2_SENSE ADC1
- PC3 PWM1_SENSE ADC1
- PA0 PWM3_SENSE ADC1
- # USART2 is for debug
- PA2 USART2_TX USART2
- PA3 USART2_RX USART2
- PA4 BATT_MON ADC1
- # SPI1 is radio
- PA5 SPI1_SCK SPI1
- PB4 SPI1_MISO SPI1
- PA7 SPI1_MOSI SPI1
- PA15 RADIO_CS CS
- PC4 RADIO_CE OUTPUT
- PC5 RADIO_PA_CTL OUTPUT
- # SPI5 is flow
- PB0 SPI5_SCK SPI5
- PA12 SPI5_MISO SPI5
- PA10 SPI5_MOSI SPI5
- PB1 FLOW_CS CS
- PB2 BOOT1 INPUT
- # I2C2 is GPS/mag
- PB10 I2C2_SCL I2C2
- PB3 I2C2_SDA I2C2
- PA13 JTMS-SWDIO SWD
- PA14 JTCK-SWCLK SWD
- # I2C1 is 20789
- PB9 I2C1_SDA I2C1
- PB8 I2C1_SCL I2C1
- PB7 LEDF OUTPUT HIGH GPIO(0)
- PB6 LEDR OUTPUT HIGH GPIO(1)
- PB5 TIM3_CH2 TIM3 PWM(2) # marked CN15 front-right
- PD2 RADIO_IRQ INPUT GPIO(100)
- # USART3 is sonix
- PC11 USART3_RX USART3
- PC10 USART3_TX USART3
- # USART6 is for GPS
- PA11 USART6_TX USART6
- PC7 USART6_RX USART6
- PA8 OF_MOTION INPUT
- PC9 TIM3_CH4 TIM3 PWM(4) # marked CN17, rear-right
- PC8 TIM3_CH3 TIM3 PWM(3) # marked CN13, rear-left
- PC6 TIM3_CH1 TIM3 PWM(1) # marked CN3, front-left
- # SPI2 is MPU
- PB13 SPI2_SCK SPI2
- PB14 SPI2_MISO SPI2
- PB15 SPI2_MOSI SPI2
- PB12 MPU_CS CS
- # SPI Device table
- SPIDEV cypress SPI1 DEVID1 RADIO_CS MODE0 2*MHZ 2*MHZ
- SPIDEV cc2500 SPI1 DEVID1 RADIO_CS MODE0 4*MHZ 4*MHZ
- SPIDEV pixartflow SPI5 DEVID2 FLOW_CS MODE3 2*MHZ 2*MHZ
- SPIDEV icm20789 SPI2 DEVID4 MPU_CS MODE3 1*MHZ 8*MHZ
- # reserve 16k for bootloader and 32k for storage
- FLASH_RESERVE_START_KB 48
- define HAL_CHIBIOS_ARCH_F412 1
- IMU Invensense SPI:icm20789 ROTATION_NONE
- # radio IRQ is on GPIO(100)
- define HAL_GPIO_RADIO_IRQ 100
- define HAL_RCINPUT_WITH_AP_RADIO 1
- define STORAGE_FLASH_PAGE 1
- define HAL_STORAGE_SIZE 15360
- # setup defines for ArduCopter config
- define TOY_MODE_ENABLED ENABLED
- define ARMING_DELAY_SEC 0
- define LAND_START_ALT 700
- define LAND_DETECTOR_ACCEL_MAX 2.0f
- define CHIBIOS_ADC_MAVLINK_DEBUG 1
- COMPASS BMM150 I2C:0:0x10 ROTATION_NONE
- define HAL_BARO_DEFAULT HAL_BARO_20789_I2C_SPI
- define HAL_BARO_20789_I2C_BUS 1
- define HAL_BARO_20789_I2C_ADDR_PRESS 0x63
|
