watchrobot/libraries/AP_HAL_ChibiOS/hwdef/f103-periph/hwdef.dat

# hw definition file for processing by chibios_pins.py

# MCU class and specific type
MCU STM32F103 STM32F103xB

# bootloader starts firmware at 25k
FLASH_RESERVE_START_KB 25

# store parameters in pages 23 and 24
define STORAGE_FLASH_PAGE 23
define HAL_STORAGE_SIZE 800

# board ID for firmware load
APJ_BOARD_ID 1000

# setup build for a peripheral firmware
env AP_PERIPH 1

# crystal frequency
OSCILLATOR_HZ 8000000

define CH_CFG_ST_FREQUENCY 1000

# assume the 128k flash part for now
FLASH_SIZE_KB 128

# board voltage
STM32_VDD 330U

# order of UARTs
UART_ORDER USART2 USART1

# a LED to flash
PA4 LED OUTPUT LOW

# USART1, connected to GPS
PA9  USART1_TX USART1 SPEED_HIGH NODMA
PA10 USART1_RX USART1 SPEED_HIGH NODMA

# USART2 for debug
PA2 USART2_TX USART2 SPEED_HIGH NODMA
PA3 USART2_RX USART2 SPEED_HIGH NODMA

define HAL_UART_NODMA

# only one I2C bus in normal config
PB6 I2C1_SCL I2C1
PB7 I2C1_SDA I2C1

PB0 MAG_CS CS

# spi bus for compass
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PA7 SPI1_MOSI SPI1

SPIDEV rm3100 SPI1 DEVID1 MAG_CS MODE0 1*MHZ 1*MHZ

# analog input
# PA5 VIN5 ADC1
define HAL_USE_ADC TRUE
define STM32_ADC_USE_ADC1 TRUE
define HAL_DISABLE_ADC_DRIVER TRUE

define HAL_NO_GPIO_IRQ
define CH_CFG_ST_TIMEDELTA 0
#define CH_CFG_USE_DYNAMIC FALSE
define SERIAL_BUFFERS_SIZE 512
define PORT_INT_REQUIRED_STACK 64

# avoid timer and RCIN threads to save memory
define HAL_NO_TIMER_THREAD
define HAL_NO_RCIN_THREAD

#defined to turn off undef warnings
define __FPU_PRESENT 0

define HAL_USE_RTC FALSE
define DISABLE_SERIAL_ESC_COMM TRUE
define NO_DATAFLASH TRUE

define DMA_RESERVE_SIZE 0

define PERIPH_FW TRUE

# MAIN_STACK is stack of initial thread
MAIN_STACK 0x100

# PROCESS_STACK controls stack for main thread
PROCESS_STACK 0x600
define HAL_DISABLE_LOOP_DELAY

# enable CAN support
PA11 CAN_RX CAN
PA12 CAN_TX CAN
define HAL_USE_CAN TRUE
define STM32_CAN_USE_CAN1 TRUE

# start with a fixed node ID so the board is usable without DNA
define HAL_CAN_DEFAULT_NODE_ID 117

define CAN_APP_VERSION_MAJOR 1
define CAN_APP_VERSION_MINOR 0
define CAN_APP_NODE_NAME "org.ardupilot.ap_periph"

define HAL_USE_I2C TRUE
define STM32_I2C_USE_I2C1 TRUE

define HAL_NO_ROMFS_SUPPORT

define HAL_UART_MIN_TX_SIZE 256
define HAL_UART_MIN_RX_SIZE 128

define CH_DBG_ENABLE_STACK_CHECK TRUE

define HAL_UART_STACK_SIZE 256
define STORAGE_THD_WA_SIZE 512

define HAL_NO_GCS
define HAL_NO_LOGGING
define HAL_NO_MONITOR_THREAD

define HAL_MINIMIZE_FEATURES 0

define HAL_BUILD_AP_PERIPH

# only one I2C bus
I2C_ORDER I2C1

COMPASS RM3100 SPI:rm3100 false ROTATION_NONE

define HAL_I2C_CLEAR_ON_TIMEOUT 0

define HAL_DEVICE_THREAD_STACK 768

define AP_PARAM_MAX_EMBEDDED_PARAM 0

define HAL_PROBE_EXTERNAL_I2C_COMPASSES
define HAL_I2C_INTERNAL_MASK 0

# disable dual GPS and GPS blending to save flash space
define GPS_MAX_RECEIVERS 1
define GPS_MAX_INSTANCES 1

# GPS+MAG
define HAL_PERIPH_ENABLE_GPS
define HAL_PERIPH_ENABLE_MAG