123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125 |
- /*
- ChibiOS - Copyright (C) 2006..2018 Giovanni Di Sirio
- Licensed under the Apache License, Version 2.0 (the "License");
- you may not use this file except in compliance with the License.
- You may obtain a copy of the License at
- http://www.apache.org/licenses/LICENSE-2.0
- Unless required by applicable law or agreed to in writing, software
- distributed under the License is distributed on an "AS IS" BASIS,
- WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- See the License for the specific language governing permissions and
- limitations under the License.
- */
- #ifndef _BOARD_H_
- #define _BOARD_H_
- /*
- * Setup for Embedded Artists LPCXpresso LPC812 board.
- */
- /*
- * Board identifiers.
- */
- #define BOARD_EA_LPC812
- #define BOARD_NAME "Embedded Artists LPCXpresso LPC812"
- /*
- * Board frequencies.
- */
- #define SYSOSCCLK 12000000
- /*
- * I/O ports initial setup, this configuration is established soon after reset
- * in the initialization code.
- * Please refer to the LPC8xx Reference Manual for details.
- */
- /* Pull-up/down */
- #define PIN_MODE_NOPULL (0<<3)
- #define PIN_MODE_PULLDOWN (1<<3)
- #define PIN_MODE_PULLUP (2<<3)
- #define PIN_MODE_REPEATER (3<<3)
- /* Hysteresis */
- #define PIN_HYS_EN (1<<5)
- /* Invert Input */
- #define PIN_INV_INPUT (1<<6)
- /* Reserved bits */
- #define PIN_RSVD (1<<7)
- /* I2C Mode */
- #define PIN_I2CMODE_STD (0<<8)
- #define PIN_I2CMODE_STDIO (1<<8)
- #define PIN_I2CMODE_FAST (2<<8)
- /* Open Drain */
- #define PIN_OPEN_DRAIN (1<<10)
- /* Input Filter Sample Clocks */
- #define PIN_SMODE_FILTER(n) ((n)<<11)
- /* Input Filter clock divider */
- #define PIN_CLKDIV_FILTER(n) ((n)<<13)
- /*
- * Pin definitions.
- */
- #define LED_RED 7
- #define LED_BLUE 16
- #define LED_GREEN 17
- /*
- * GPIO 0 initial setup.
- */
- /*#define VAL_PIO0_0 PIN_MODE_PULLUP*/
- /*#define VAL_PIO0_1 PIN_MODE_PULLUP*/
- /*#define VAL_PIO0_2 PIN_MODE_PULLUP*/
- /*#define VAL_PIO0_3 PIN_MODE_PULLUP*/
- /*#define VAL_PIO0_4 PIN_MODE_PULLUP*/
- /*#define VAL_PIO0_5 PIN_MODE_PULLUP*/
- /*#define VAL_PIO0_6 PIN_MODE_PULLUP*/
- #define VAL_PIO0_7 PIN_MODE_NOPULL
- /*#define VAL_PIO0_8 PIN_MODE_PULLUP*/
- /*#define VAL_PIO0_9 PIN_MODE_PULLUP*/
- /*#define VAL_PIO0_10 PIN_MODE_PULLUP*/
- /*#define VAL_PIO0_11 PIN_MODE_PULLUP*/
- /*#define VAL_PIO0_12 PIN_MODE_PULLUP*/
- /*#define VAL_PIO0_13 PIN_MODE_PULLUP*/
- /*#define VAL_PIO0_14 PIN_MODE_PULLUP*/
- /*#define VAL_PIO0_15 PIN_MODE_PULLUP*/
- #define VAL_PIO0_16 PIN_MODE_NOPULL
- #define VAL_PIO0_17 PIN_MODE_NOPULL
- /* UART0: TXD = P0.4, RXD = P0.0)*/
- #define VAL_PINASSIGN0 ((0xFFFF0000) | (0<<8) | (4))
- /*#define VAL_PINASSIGN1 0xFFFFFFFF*/
- /*#define VAL_PINASSIGN2 0xFFFFFFFF*/
- /*#define VAL_PINASSIGN3 0xFFFFFFFF*/
- /*#define VAL_PINASSIGN4 0xFFFFFFFF*/
- /*#define VAL_PINASSIGN5 0xFFFFFFFF*/
- /*#define VAL_PINASSIGN6 0xFFFFFFFF*/
- /*#define VAL_PINASSIGN7 0xFFFFFFFF*/
- /*#define VAL_PINASSIGN8 0xFFFFFFFF*/
- #define VAL_GPIO0DIR (PAL_PORT_BIT(LED_RED) | \
- PAL_PORT_BIT(LED_BLUE) | \
- PAL_PORT_BIT(LED_GREEN))
-
- #define VAL_GPIO0DATA (PAL_PORT_BIT(LED_RED) | \
- PAL_PORT_BIT(LED_BLUE) | \
- PAL_PORT_BIT(LED_GREEN))
- #if !defined(_FROM_ASM_)
- #ifdef __cplusplus
- extern "C" {
- #endif
- void boardInit(void);
- #ifdef __cplusplus
- }
- #endif
- #endif /* _FROM_ASM_ */
- #endif /* _BOARD_H_ */
|