danny wang 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
..
generator 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
lua 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
scripts 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
AP_Scripting.cpp 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
AP_Scripting.h 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
README.md 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
lua_bindings.cpp 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
lua_bindings.h 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
lua_boxed_numerics.cpp 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
lua_boxed_numerics.h 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
lua_generated_bindings.cpp 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
lua_generated_bindings.h 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
lua_scripts.cpp 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu
lua_scripts.h 6b2cb6fa39 this N3 net clean robot use bfd1.5V6 2 lat temu

README.md

AP_Scripting

Enabling Scripting Support in Builds

Scripting is automatically enabled on all boards with at least 1MB of flash space. The following example enables scripting, builds the ArduPlane firmware for the Cube, and uploads it.

$ waf configure --board=CubeBlack

$ waf plane

$ waf plane --upload

To run SITL you can simply use the sim_vehicle.py script which will wrap the configuration, compilation, and launching of the simulation into one command for you.

$ Tools/autotest/sim_vehicle.py -v ArduPlane

Once you have a vehicle flashed with scripting you need to set the SCR_ENABLE parameter to 1 to enable scripting and reboot.

Adding Scripts

The vehicle will automatically look for and launch any scripts that are contained in the scripts folder when it starts. On real hardware this should be inside of the APM folder of the SD card. In SITL this should be in the working directory (typically the main ardupilot directory).

An example script is given below:

function update () -- periodic function that will be called
  current_pos = ahrs:get_position()
  home = ahrs:get_home()
  if current_pos and home then
    distance = current_pos:get_distance(ahrs:get_home()) -- calculate the distance from home
    if distance > 1000 then -- if more then 1000 meters away
      distance = 1000;      -- clamp the distance to 1000 meters
    end
    servo.set_output_pwm(96, 1000 + distance) -- set the servo assigned function 96 (scripting3) to a proportional value
  end

  return update, 1000 -- request to be rerun again 1000 milliseconds (1 second) from now
end

return update, 1000 -- request to be rerun again 1000 milliseconds (1 second) from now